Diesel Engine Split Casing Fire Pump
Summarize of 1000m3/Hr Irrigation Diesel Water Pump
Model QS Horizontal split case irrigation pump is a single-stage double-suction horizontal split centrifugal pump and used to transport pure water and the liquid of both physical and chemical nature similar to those of water, the maximum temperature of which must not be over 80ºC , suitable for water supply and drainage in factories, mines, cities and electric stations, waterlogged land drainage and irrigation of farming land and carious hydraulic projects.
Application for 1000m3/Hr Irrigation Diesel Water Pump
Aerospace Oil & Gas
Building industry Power Station
Chemical Petro-Chemical
General Industry Pharmaceutical
Marine Pulp & Paper
Mining & Aggregate Water & Waste water
Advantage about 1000m3/Hr Irrigation Diesel Water Pump
20 years in producing irrigation pump
Independent Design
advanced technology from Australia, Canada, America
Specialized Test Equipment
Anti-rust treatment casting
Supply reasonable suggestion for choosing pumps
OEM available
Pump Structure about 1000m3/Hr Irrigation Diesel Water Pump
1. Irrigation pump Casing
The volute casing is split on the horizontal centerline with the suction and discharge nozzle cast integral with the pump casing. The upper casing is accurately located on the lower half by the use of dowel pins. The upper casing can be removed to inspect the interior of the pump without disturbing the pipe connections or pump alignment. The suction and discharge flanges contain tapped holes for vacuum and pressure gauge. At the bottom of the flanges, there are tapped plugs for water drainage.
2. Impeller
The impeller is static-balance calibrated, fixed with the muff and the muff nuts in both sides and its axial position can be adjusted via the nuts and axial force gets balanced by means of the symmetrical arrangement of its blades, there may be residual axial force which is borne by the bearing at the axle end.
3. Shaft
The pump shaft is supported by two single-column centripetal ball bearings, which are mounted inside of the bearing body on both ends of the pump and lubricated with grease. The dual-suction seal ring is used to reduce the leak at the impeller
4. Seal Type
There is gland seal type and mechanical seal type.
Direction of Rotation about Large Flow Centrifugal Double Suction Horizontal Split Case Irrigation Pump
The irrigation pump moves CW viewing from the clutch to it. The pump moving CCW can also be produced.
Materials about 1000m3/Hr Irrigation Diesel Water Pump
Irrigation pump general material is cast iron, main include pump casing, pump cover, impeller, seal ring and shaft sleeve, shaft is carbon steel. We could also produce as your requirements, such as nodular cast iron, cast steel, bronze and stainless steel etc.
Performance table list about 1000m3/Hr Irrigation Diesel Water Pump
Structure about 1000m3/Hr Irrigation Diesel Water Pump
| 1.Bearing |
2.Framework oil seal |
3. Bearing gland |
4.Pump casing |
5.Packing gland |
6.Packings |
| 7.Packing ring |
8.Packing sleeve |
9.Shaft sleeve |
10.Pump cover |
11.Impeller |
12.Washing pipe |
| 13.O ring |
14.Casing seal ring |
15.Mechanical seal liner |
16.O ring |
17. Mechanical seal |
| 18.Mechanical seal gland |
19.Water retaining ring |
20.O ring |
21.Bearing housing at driven end |
| 22.Shaft |
23.Couplings |
24.C type key |
25.Frame oil seal |
26.Ring for shaft |
27.Bearing junk ring |
| 28.Cylindrical pin |
29.Mechanical seal |
30.Cylindrical pin |
31.B type key |
32.Packing seal |
33.Seal |
| 34.Nut lock washer |
35.Round nut |
36.Bearing inner liner |
37.Pump end bearing housing |
38.Bearing spacer |
RFQ about 1000m3/Hr Irrigation Diesel Water Pump
Centrifugal irrigation pump power loss
There only a part of the mechanical power of the centrifugal pump getting from the driver equipment, convert to the centrifugal power and then delivered to the liquid power. The another part was loss. The reasons are below:
1. Hydraulic loss: Created for the liquid impact, vortex and friction in the pump. The impact and vortex hydraulic loss is because of the the liquid change the flow direction. Besides, when the liquid flow, it will have friction when meet the pump passageway.This kind of loss depend on the length, volume, shape, and surface roughness of the passageway and the liquid flow speed and other character.
2. Volume loss: It resulted for the powered liquid will channeling are leakage. The general pump volume efficiency is 0.93~0.98%. Improve the seal ring and shaft seal construction, can reduce the volume loss and increase the volume efficiency.
3. Mechanical loss: It is caused by the friction of liquid and impeller plate surface, also named dick friction loss of impeller, and the pump shaft friction when rotated in the packing, bearing, balancing parts and other mechanical parts.
Please feel free to contact me Helen.Mobile:86-18032481573
Factory
FAQ
Q1. Are you a manufacturer?
Yes, we have been in centrifugal pumps manufacturing and marketing industry over 32 years.
Q2. What markets do your pumps export to?
Europe, North & South America, South-East Asia, Africa, Oceanica, Middle East countries. Our overseas agent in Italy, Russia, America and Africa are gradually improving.
Q3. What information should I let you know if I want to get a quotation?
Please let us know the pump capacity, head, medium, operation situation, quantity, etc. As much as your provide, the precision and accurate model selection.
Q4. Is it available to print our own brand on the pump?
Totally acceptable as international rules.
Q5. How can I get the price of your pump?
You can connect with us through any of the following contact information. Our personalized service person will respond you within 24 hours.
Welcome to visit our factory!
CONTACT ME
Audited Supplier 
){kind=link}
){kind=link}